Connectors

SHOKZ USB-C Adapter

Réf. : 778070

Slot Bracket with 2 x eSATA Ports

Réf. : 145080

Connect this slot bracket to the SATA port of your motherboard or any other SATA controller board. It adds two external eSATA connectors.

Main features:

- 2 x SATA internal connectors
- 2 x eSATA female connectors
- Cable length: 30 cm

M.2 NGFF SATA to 2.5" SATA Adapter

Réf. : 307607

6Gbps SATA III H/W RAID Controller

Product benefits:

- Rapid SSD to SATA conversion
- Natural air flow
- Same size than a 2.5'' SSD
- Can be easily adapted into a PC, laptop
- Transparent for the system
- Hardware-based RAID 1/ SPAN and PM

Main features:

- Converts 2x M.2 NGFF SATA based SSD to a standard 2.5'' 7mm SATA drive
- Supports SATA I, SATA II, SATA III Host port
- Supports 6Gbps, 3Gbps SATA-based M.2 NGFF 80/60/42/30 mm SSD
- M.2 NGFF type 2280-D5-B connector on board
- Movable M.2 NGFF stand-off and multiple plated-holes supports type 2280, 2260, 2242 and 2230 SSD
- Supports dual-sided SSD module 1.5mm component height on the top and bottom side
- Supports H/W RAID 1, SPAN (Big Drive) and PM (2Drives) Modes
- Does not support PM (2 Drives) Mode if SATA I or no Port Multiplier compatible
- SATA Host connection
- 22-pin SATA (Signals and Power) male connector on board
- 2x M.2 SSD ACT LED
- Transparent to the operating system, no driver required on Windows, Mac and Linux
- Provides Windows and Mac GUI to configure RAID modes and monitor RAID status
- Includes 7mm height 2.5'' drive metal frame with 8 mounting holes and 4 HDD screws
- Compatible with 2.5'' SATA drive dimension : 100.45mm x 69.85mm x 7mm

Slot Bracket with 2 x DB9 Ports

Réf. : 145072

The slot bracket is to be connected to a motherboard or serial RS-232 card. It provides two external
DB9 male connectors.

Main features :
- 2 x HE-10 motherboard connectors
- 2 x DB-9 male connectors
- Cable length: 18 cm

HE-10 Connector Specifications:
2 4 6 8 10 (Pin # 10 poka yoke)
1 3 5 7 9 (Pin # 1 is marked)

Wiring Diagram
HE-10 - DB9 male - Signal
1 1 CD
2 2 RD
3 3 TD
4 4 DTR
5 5 Gnd
6 6 DSR
7 7 RTS
8 8 CTS
9 9 RI
10 not used

Molex to PCI Express 8-pin power adapter cable- 15 cm

Réf. : 146693

This adapter changes the 2 x Molex power connectors into a PCI-Express 8-pin connector to supply the
power to a graphic card.
Indispensable for the power supplies that don't have any PCI Express power connector.

Product features:

- Input connectors: 2 x Molex 4-pin male connectors
- Output connectors: 1 x PCI Express 8-pin connector
- Cable length: 15 cm.

2-in-1 SATA cable with Molex power connector- 50 cm

Réf. : 147551

This adapter cable makes it possible to install and connect a SATA SSD in a computer which lacks SATA power connectors. The combo connector is compatible with Molex connectors.

Product features:

- Input connectors : 1 x 4-pin Molex male + 1 x SATA
- Output connectors: 1 x SATA (data + power)
- Cable length : 20 cm (power supply / 50 cm (SATA)

Slim SATA (CD/DVD) to SATA Adapter

Réf. : 146341

Changes the Slim SATA connector of a slim optical drive (CD/DVD) into a SATA connector with power
supply.
Compatible with Windows, Mac, and Linux operating systems, for which no drivers are required.

Main features:

- Slim SATA connector on the optical drive side
- SATA (data+power) connector on the motherboard side
- Without cable

Molex Y cable + floppy- 20 cm

Réf. : 146630

For additional device connection, such as optical drive. Indispensable for the power supplies which do not have any floppy connector.


Main features:

- Input connector: 1 x 4-pin Molex male
- Output connectors: 1 x floppy female
- Cable length: 20 cm

Micro SATA (SSD) to SATA Adapter

Réf. : 146310

Changes the micro SATA SSD connector into SATA connector with power supply. Compatible with Windows,
Mac, Linux operating systems, for which no drivers are needed.

Main features:

- Micro SATA connector on the SSD side
- SATA (Data + Power) connector on the motherboard side
- Without cable.

Sata Adapter for CD/DVD Slim Drive with Power Supply

Réf. : 146330

Can change the Slim SATA connector of a Slim optical drive (CD/DVD) into a SATA connector.
Compatible with Windows, Mac, Linux operating systems. No drivers required.

Main features:

- Slim SATA connector on the optical drive side
- 7-pin SATA & 4-pin Molex connectors on the motherboard side
- Cable length: 50 cm

PCI Express Power adapter cable 6 to 8 pins

Réf. : 146695

Changes a 6-pin PCI-Express power connector into a 8-pin PCI-Express connector, to supply the power to a PCI-e graphic card.
A low-cost solution for the power supplies that don't have any PCI-e power connector.

Product features:

- Input connector: 1 x 6-pin PCI-Express connector
- Output connector: 1 x 8-pin PCI-Express connector
- Cable length: 10 cm.

SATA cable with 2 angled down connectors- 50 cm

Réf. : 147691

This SATA cable allows the connection of devices sucha as HDDs, SSDs, SATA optical drives to a motherboard or controller with SATA interface.
Compatible with SATA, SATA2 and SATA3.0 (6Gbps)

Product features:

- Input connector: 1 x Serial ATA angled down
- Output connector: 1 x Serial ATA angled down
- Cable length: 50 cm.

24-pin to 20-pin power cable adapter for motherboard-10 cm

Réf. : 314071

With this adapter cable, you can connect a 24-pin ATX power supply to a motherboard equipped only with 20-pin ATX connectors.
The wiring drawing complies with EPS/12V specifications on the 24-pin side and to the ATX2.x specifications on the 20-pin side.

Main features:

- Input connector: 1 x 24-pin ATX
- Output connector: 1 x 20-pin ATX
- Cable length: 10 cm

Slot bracket with 2 x USB2. ports

Réf. : 146698

Slot bracket for connection to your motherboard. It provides 2 external USB2.0 ports.
With a 25-cm cable.

Main features:

- Internal connector: 10-pin DIP (2 x 5)
- Bracket connectors: USB2.0 female type A
- Cable length: 25 cm.

Slot Bracket with 1 x DB9 Serial Port

Réf. : 145071

The standard slot bracket can be connected to a motherboard or serial RS-232 card. It provides an external DB9 male connector.
The bracket is equipped with a serial port and a HE 10 port connected by a 18-cm long cable.

Main features:
- Motherboard connector: female HE-10
- Serial connector: DB-9 male
- Cable length: 18 cm

HE-10 Connector Specifications:
2 4 6 8 10 (Pin # 10 poka yoke)
1 3 5 7 9 (Pin #1 is marked)

Wiring Diagram :
HE-10 - DB9 male - Signal
1 1 CD
2 2 RD
3 3 TD
4 4 DTR
5 5 Gnd
6 6 DSR
7 7 RTS
8 8 CTS
9 9 RI
10 not used

Otterbox USB C-C cable 1M

Réf. : 766529

Blind Slot Bracket- Bag of 10pcs

Réf. : 740351

Blind slot brackets by 10 pieces.

Sata cable- 100 cm

Réf. : 314000

Connect a HDD, SSD or a SATA optical drive to a motherboard or SATA host controller.
Compatible with SATA, SATA 2 and SATA 3.0 (6Gbps) interfaces.

Product features:

- Input connector: 1 x Serial ATA
- Output connector: 1 x Serial ATA
- Cable length: 1 m

IDE adapter cable for 2,5" HDD

Réf. : 300991

IDE adapter cable for connection of a 2.5'' IDE HDD (44 pins) to a standard 40-pin IDE motherboard ribbon cable over Molex power supply plug.
This adapter cable is recommended when you need to retrieve data from a desktop computer to an external HDD enclosure.

Main features:

- On the motherboard side: HE10 40-pin (data) connector and Molex (power supply) connector
- On the IDE 2.5'' HDD side: HE10 44-pin

Molex Y Power cable- 20 cm

Réf. : 146600

Molex Y cable for additional device connection.

Product features:

- Input connector: 1 x 4-pin Molex male connector
- Output connectors: 2 x 4-pin female Molex connectors
- Cable length: 20 cm.

AT to ATX motherboard power adapter cable

Réf. : 147531

Ideal to install an old-generation AT P8/P9 motherboard into an up-to-date PC case

Main features:

- Input connector: 1 x 20-pin ATX
- Output connector: 1 x AT (P8/P9)
- Cable length: 20 cm

Bracket Type-C USB 3.1 Gen2 to Internal USB 3.1

Réf. : 146700

Data + Power SATA extension cable- 50cm

Réf. : 147500

This extension calbe is 50-cm longer than the standard cables, ideal for HDD connection.
Includes a data and a power supply connectors. Practical for large PC cases.

Product features :

- Input connector: 1x SATA male (power + data)
- Output connector:1x SATA Female (power + data)
- Cable length: 50 cm.

ATX P4 power extension cable for motherboard-20 cm

Réf. : 147562

You can extend the ATX P4 (ATX12V1) existing power cable for motherboard connection. This cable supplies the power to the CPU, and without it, the system cannot be powered on.

Main features:

- Input connector: 1 x ATX P4 female
- Output connector: 1 x ATX P4 male
- Cable length: 20 cm

PCI Express 6-pin Y power cable- 15 cm

Réf. : 146694

Split a PCI-Express 6-pin power connector into 2 x PCI-e connectors to supply the power to a
graphic card that requires 2 x power supplies or two graphic cards.
An indispensable low-cost solution for the power supplies that are not equipped with a PCI-Express power supply.

Product features:

- Input connector: 1 x PCI-Express 6-pin connector
- Output connectors: 2 x PCI-Express 6-pin connectors
- Cable length: 15 cm.