Fiber converters and chassis

TP-LINK MC220L Gigabit Ethernet Media Converter

Part/number : 311898

The MC220L is a media converter designed to convert 1000BASE-SX/LX/LH fiber to 1000Base-T copper media or vice versa. Designed under IEEE802.3ab 1000Base-T and IEEE802.3z 1000Base-SX/LX/LH standards, the MC220L is designed for use with multi-mode/single-mode fiber cable utilizing the SC/LC-Type connector. It works at 850nm on both transmitting and receiving data when adopting multi-mode fiber and 1310nm on both transmitting and receiving data when adopting single-mode.

Main Features:

•Complies with IEEE 802.3ab and IEEE 802.3z
•Hot-swappable FX port
•Extends fiber distance up to 0.55km(0.342 miles) for multi-mode fiber and 10km(6.2 miles) for single-mode fiber

TP-LINK MC111CS WDM Fast Ethernet Media Converter

Part/number : 311918

The MC111CS is a media converter designed to convert 100BASE-FX fiber to 100Base-TX copper media or vice versa. Adopting WDM technology, MC111CS takes only one fiber cable to transmit and receive data, which will save half the cabling. Designed following the IEEE 802.3u 10/100Base-TX and 100Base-FX standards, the MC111CS is compatible with single-mode fiber cable over the SC-Type connector. The MC111CS supports longwave (LX) laser specification at a full wire speed forwarding rate. It works at 1550nm on transferring data and at 1310nm on receiving data. So the other end device to cooperate with the MC111CS should work at 1310nm on transferring data and at 1550nm on receiving data. Another TP-LINK´s media converter MC112CS is just one of the examples to cooperate with MC111CS.

Other features of this module include the ability to be used as a stand-alone device (no chassis required) or with TP-LINK´s 19´´ system chassis, Auto MDI/MDI-X for TX port, Auto negotiation of duplex mode on TX port, and front panel status LEDs. The MC111CS will transmit at extended fiber optic distances utilizing single-mode fiber up to 20 kilometers(12.4 miles).

•Complies with 802.3u 10/100Base-TX, 100Base-FX standards
•Link Fault Passthrough and Far End Fault minimize the loss caused by link failure timely
•Adopts WDM technology, transmitting and receiving data on one single fiber

TP-LINK TL-SM321B-2 1000BASE BX WDM BIDIRECTIONAL SFP MODULE

Part/number : 311908

TP-LINK MC111CS WDM Fast Ethernet Media Converter

Part/number : 311904

The MC111CS is a media converter designed to convert 100BASE-FX fiber to 100Base-TX copper media or vice versa. Adopting WDM technology, MC111CS takes only one fiber cable to transmit and receive data, which will save half the cabling. Designed following the IEEE 802.3u 10/100Base-TX and 100Base-FX standards, the MC111CS is compatible with single-mode fiber cable over the SC-Type connector. The MC111CS supports longwave (LX) laser specification at a full wire speed forwarding rate. It works at 1550nm on transferring data and at 1310nm on receiving data. So the other end device to cooperate with the MC111CS should work at 1310nm on transferring data and at 1550nm on receiving data. Another TP-LINK´s media converter MC112CS is just one of the examples to cooperate with MC111CS.

Other features of this module include the ability to be used as a stand-alone device (no chassis required) or with TP-LINK´s 19´´ system chassis, Auto MDI/MDI-X for TX port, Auto negotiation of duplex mode on TX port, and front panel status LEDs. The MC111CS will transmit at extended fiber optic distances utilizing single-mode fiber up to 20 kilometers(12.4 miles).

•Complies with 802.3u 10/100Base-TX, 100Base-FX standards
•Link Fault Passthrough and Far End Fault minimize the loss caused by link failure timely
•Adopts WDM technology, transmitting and receiving data on one single fiber

TP-LINK MC111CS WDM Fast Ethernet Media Converter

Part/number : 311903

The MC111CS is a media converter designed to convert 100BASE-FX fiber to 100Base-TX copper media or vice versa. Adopting WDM technology, MC111CS takes only one fiber cable to transmit and receive data, which will save half the cabling. Designed following the IEEE 802.3u 10/100Base-TX and 100Base-FX standards, the MC111CS is compatible with single-mode fiber cable over the SC-Type connector. The MC111CS supports longwave (LX) laser specification at a full wire speed forwarding rate. It works at 1550nm on transferring data and at 1310nm on receiving data. So the other end device to cooperate with the MC111CS should work at 1310nm on transferring data and at 1550nm on receiving data. Another TP-LINK´s media converter MC112CS is just one of the examples to cooperate with MC111CS.

Other features of this module include the ability to be used as a stand-alone device (no chassis required) or with TP-LINK´s 19´´ system chassis, Auto MDI/MDI-X for TX port, Auto negotiation of duplex mode on TX port, and front panel status LEDs. The MC111CS will transmit at extended fiber optic distances utilizing single-mode fiber up to 20 kilometers(12.4 miles).

•Complies with 802.3u 10/100Base-TX, 100Base-FX standards
•Link Fault Passthrough and Far End Fault minimize the loss caused by link failure timely
•Adopts WDM technology, transmitting and receiving data on one single fiber

PLANET MGB-TSX2 SX SFP Module up to 2KM -45/85°C

Part/number : 411796

TP-LINK MC111CS WDM Fast Ethernet Media Converter

Part/number : 311921

The MC111CS is a media converter designed to convert 100BASE-FX fiber to 100Base-TX copper media or vice versa. Adopting WDM technology, MC111CS takes only one fiber cable to transmit and receive data, which will save half the cabling. Designed following the IEEE 802.3u 10/100Base-TX and 100Base-FX standards, the MC111CS is compatible with single-mode fiber cable over the SC-Type connector. The MC111CS supports longwave (LX) laser specification at a full wire speed forwarding rate. It works at 1550nm on transferring data and at 1310nm on receiving data. So the other end device to cooperate with the MC111CS should work at 1310nm on transferring data and at 1550nm on receiving data. Another TP-LINK´s media converter MC112CS is just one of the examples to cooperate with MC111CS.

Other features of this module include the ability to be used as a stand-alone device (no chassis required) or with TP-LINK´s 19´´ system chassis, Auto MDI/MDI-X for TX port, Auto negotiation of duplex mode on TX port, and front panel status LEDs. The MC111CS will transmit at extended fiber optic distances utilizing single-mode fiber up to 20 kilometers(12.4 miles).

•Complies with 802.3u 10/100Base-TX, 100Base-FX standards
•Link Fault Passthrough and Far End Fault minimize the loss caused by link failure timely
•Adopts WDM technology, transmitting and receiving data on one single fiber

TP-LINK MC112CS WDM Fast Ethernet Media Converter

Part/number : 311922

The MC112CS is a media converter designed to convert 100BASE-FX fiber to 100Base-TX copper media or vice versa. Adopting WDM technology, MC112CS takes only one fiber cable to transmit and receive data, which will save half cabling cost for you. Designed under IEEE 802.3u 10/100Base-TX and 100Base-FX standards, the MC112CS is designed for use with single-mode fiber cable utilizing the SC-Type connector. The MC112CS supports longwave (LX) laser specification at a full wire speed forwarding rate. It works at 1310nm on transferring data and at 1550nm on receiving data. So the other end device to cooperate with the MC112CS should work at 1550nm on transferring data and at 1310nm on receiving data. Another TP-LINK+s media converter MC111CS is just one of the examples to cooperate with MC112CS.

Other features of this module include the ability to be used as a stand alone device (no chassis required), Auto MDI/MDI-X for TX port, Auto negotiation of duplex mode on TX port, and front panel status LEDs. The MC112CS will transmit at extended fiber optic distances utilizing single-mode fiber
up to 20 kilometers(12.4 miles).

Main Features:

•Complies with 802.3u 10/100Base-TX, 100Base-FX standards.
•Link Fault Passthrough and Far End Fault minimize the loss caused by link failure timely
•Adopts WDM technology, transmitting and receiving data on one single fiber

Energy Star External Power Adapter for all universal Media Converters (supports

Part/number : 522221

TP-LINK MC100CM Fast Ethernet Media Converter

Part/number : 311911

The MC100CM is a media converter designed to convert 100BASE-FX fiber to 100Base-TX copper media or vice versa. Designed under IEEE 802.3u 10/100Base-TX and 100Base-FX standards, the MC100CM is designed for use with multi-mode fiber cable utilizing the SC-Type connector. The MC100CM supports longwave (LX) laser specification at a full wire speed forwarding rate. It works at 850nm on both transmitting and receiving data.

Other features of this module include the ability to be used as a stand alone device (no chassis required) or with TP-LINK´s 19´´system chassis, Auto MDI/MDI-X for TX port, Auto negotiation of duplex mode on TX port, supports both 5VDC and 9VDC external power supply and front panel status LEDs. The MC100CM will transmit at extended fiber optic distances utilizing multi-mode fiber up to 2
kilometers(1.2 miles).

•Complies with 802.3u 10/100Base-TX, 100Base-FX standards
•Link Fault Passthrough and Far End Fault minimize the loss caused by link failure timely
•Provides switch configuration of Half-Duplex / Full-Duplex transfer mode for FX port
•Extends fiber distance up to 2km(1.2 miles)

TP-LINK MC110 CS Fast Ethernet Media Converter

Part/number : 311914

The MC110CS is a media converter designed to convert 100BASE-FX fiber to 100Base-TX copper media or vice versa. Designed under IEEE 802.3u 10/100Base-TX and 100Base-FX standards, the MC110CS is compatible with single-mode fiber cable over the SC-Type connector. The MC110CS supports longwave (LX) laser specification at a full wire speed forwarding rate. It works at 1310nm on both transmitting and receiving data.

Other features of this module include the ability to be used as a stand-alone device (no chassis required) or with TP-LINK´s 19´´ system chassis, Auto MDI/MDI-X for TX port, Auto negotiation of duplex mode on TX port, supports both 5VDC and 9VDC external power supply and front panel status LEDs. The MC110CS will transmit at extended fiber optic distances utilizing single-mode fiber up to 20 kilometers(12.4 miles).

Main Features:

•Complies with 802.3u 10/100Base-TX, 100Base-FX standards.
•Link Fault Passthrough and Far End Fault minimize the loss caused by link failure timely
•Provides switch configuration of Half-Duplex / Full-Duplex transfer mode for FX port.
•Extends fiber distance up to 20km(12.4 miles)

TP-LINK MC210CS Gigabit Ethernet Media Converter

Part/number : 311925

The MC210CS is a media converter designed to convert 1000BASE-LX/LH fiber to 1000Base-T copper media
or vice versa. Designed under IEEE802.3ab 1000Base-T and IEEE802.3z 1000Base-LX/LH standards, the MC210CS is designed for use with single-mode fiber cable utilizing the SC-Type connector. The MC210CS supports longwave (LX) laser specification at a full wire speed forwarding rate. It works at
1310nm on both transmitting and receiving data.

Other features of this module include the ability to be used as a stand alone device (no chassis required) or with TP-LINK´s 19´´system chassis, Auto MDI/MDI-X for TX port, and front panel status LEDs. The MC210CS will transmit at extended fiber optic distances utilizing single-mode fiber up to 15 kilometers(9.3 miles).

•Complies with IEEE 802.3ab and IEEE 802.3z
•Provides switch configuration of Force /Auto transfer mode for FX port
•Extends fiber distance up to 15km(9.3 miles)

TL-SM5110-SR 10Gbase-SR SFP+ LC Transceiver 300m

Part/number : 311949

TP-LINK MC200CM Gigabit Ethernet Media Converter

Part/number : 311915

The MC200CM is a media converter designed to convert 1000BASE-SX fiber to 1000Base-T copper media or
vice versa. Designed under IEEE802.3ab 1000Base-T and IEEE802.3z 1000Base-SX standards, the MC200CM is compatible with multi-mode fiber cable utilizing the SC-Type connector. The MC200CM supports shortwave (SX) laser specification at a full wire speed forwarding rate. It works at 850nm on both transmitting and receiving data.

Other features of this module include the ability to be used as a stand alone device (no chassis required) or with TP-LINK´s 19´system chassis, Auto MDI/MDI-X for TX port, and front panel status LEDs. The MC200CM will transmit at extended fiber optic distances utilizing multi-mode fiber up to 0.55 kilometers(0.342 miles).

•Complies with IEEE 802.3ab and IEEE 802.3z
•Provides switch configuration of Force /Auto transfer mode for FX port
•Extends fiber distance up to 0.55km(0.342 miles)

Dexlan 10/100 sfp 100FX port media converter

Part/number : 311690

This media converter is equipped with an STP RJ-45 port with auto-negotiation function and an SFP slot. You can adapt the media converter depending on your network, by inserting a MiniGBiC module (not included) for single-mode or multimode link implementation.
Depending on the transceiver, the transmission distance can reach up to 2km in multimode fiber and up to 10km in single-mode fiber.

Specifications:

- Compatible with IEEE802.3 and IEEE802.3u standards
- Data transfer rate up to 100Mbps in Full Duplex mode on the fiber and copper ports
- Auto-negotiation and Auto MDI/MDI-X functions supported by the RJ-45 port
- Compatible with IEEE802.1Q VLAN Tag and Spanning Tree protocols
- SFP slot for 100FX multimode or single-mode transceiver insertion, hot swappable
- 4 DIP switches for speed override and Link Fault Pass-through function setup

10/100 SFP 100FX PORT MEDIA CONVERTER

Part/number : 311691

Wall mountable and Rackmountable Tray for 1 Unit of Media Converter

Part/number : 522011

SFP ALLIED TELESIS SPLX10A

Part/number : 522007

MEDIA CONVERTER MULTIMODE 100FX SC 2 RJ45-2 KM

Part/number : 311753

GIGABIT 10/100/1000 TO SFP PORT MEDIA CONVERTER

Part/number : 311791

MEDIA CONVERTER SINGLE MODE 100FX SC+LFP-25KM

Part/number : 311726

Media converter Fast Ethernet to 100FX SC Multimode 2KC

Part/number : 311703

PLANET FT-802 TX to FX Bridge Media Converter- 2km

Part/number : 411702

PLANET FT-802 TX to FX is a Fast Ethernet Bridge 100Base-FX fiber to 10/100Base-TX shielded twisted pair (STP) converter. It supports both half-duplex and full-duplex operations and a variety of fiber
options. The converter auto-adapts to the highest level of performance supported by the device connected to the STP port. When the device is a switch or a workstation that supports full duplex, the converter adapts to the full-duplex mode and provides an effective 200Mbps bandwidth. When the connected device is a hub or a workstation that supports only half duplex, the converter adapts to the half-duplex mode and provides the nominal 100Mbps bandwidth. An override switch provides total manual control over the half/full-duplex operation, in fiber-optic interface. The fiber port of
the converter operates at 1310 nm and uses SC connectors over multimode fiber.

The FT-80x series is with LFP (Link Fault Pass through function) (LLCF/LLR) and the DIP switch design. LLCF/LLR can immediately alarm administrators in case of a problem and provide efficient solutions to monitoring the net. The DIP switch allows you to disable or enable the LFP function.

LLCF (Link Loss Carry Forward) means that when a device is connected to the converter and the TP line loses the link, the converter's fiber will disconnect the transmission link. LLR (Link Loss Return) means that when a device is connected to the converter and the fiber line loses the link, the converter's fiber will disconnect the transmission link. Both can immediately alarm administrators of the problem on the link media and provide efficient solutions to monitoring the net.

Complies with IEEE 802.3, IEEE 802.3u 10/100Base-TX, 100Base-FX Standards
- Connectors: One RJ-45 (Auto-MDI/MDI-X) twisted pair, EIA568
- One fiber-optic, 1310nm wavelength, SC connector- 2km on multimode fiber
- Data Transfer Rate:
- TP: 10/100Mbps
- FX: 100Mbps
Duplex mode support:
- Full or half-duplex mode by Auto-Negotiation (TP)
- Full or half-duplex mode by DIP-switch (FX)
- LED indicators: PWR, FX LNK/ACT, FX FDX/COL, TP 100, TP LNK/ACT, TP FDX/COL
- DIP-switch: 2 DIP-switches
- Rear DIP-switch: FX duplex mode selection
- Side DIP-switch: LFP (Link Fault Pass-through) mode selection

Allied at-spsx sfp optical module, 1000SX, 220m/550m

Part/number : 522799

PLANET GT-805A Gigabit SFP Media Converter

Part/number : 411805

The PLANET GT-805A is a Gigabit Ethernet converter: 10/100/1000Base-T to 1000Base-SX/LX. It is equipped with 1 x SFP slot for fiber transceiver module insertion and 1 x RJ-45 port with auto negotiation and MDI/MDI-X functions.
The converter supports LFP control (Link Fault Pass-through) so that the administrator will be informed in case of a problem occurring on the link (Link Loss Carry Forward & Link Loss Return).

Specifications:

- 1 x RJ-45 10/100/1000Mbps port
- 1 x SFP slot for fiber module insertion
- Connection distance: 62.5/125µm in multimode fiber up to 220m & 50/125µm in single-mode fiber up to 550m.
- External power supply: 110/230V- 5V/2A
- Compatible with MC1500/MC700 rackmount chassis from PLANET
- Power consumption: 5.6 Watts
- Dimensions: 97 x 70 x 26mm

ALLIED AT-SPFX/2 SFP Optical Module 100FX Multimode 2km

Part/number : 522699

PLANET GT-802 Gigabit 1000SX Media Converter

Part/number : 411802

Key features:

- Complies with IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.3ab 1000Base-T, IEEE 802.3z 1000Base-SX/LX.
- TP port supports 10/100/1000Base-T auto-negotiation and auto-MDI/MDI-X.
- 1000Base-SX: 50/125µm or 62.5/125µm multi-mode fiber cable, up to 220/550m (GT-802).
- Layer 2 key Feature
- IEEE 802.3x full-duplex flow-control and back-pressure in half-duplex eliminates the loss of packets
- Supports auto MDI/MDI-X function
- Store-and-Forward mechanism
- Non-blocking full wire-speed forwarding rate
- Media conversion between 10/100/1000Base-T and 1000Base-SX/LX.
- Wallmounting design
- LED indicators for easy network diagnostic
- LFP function available by DIP Switch
- Supports jumbo frames up to 9k
- Compact size, easy installation

10/100/1000 to 1000LX Media conv. W/SFP SingleMode 20KM LC

Part/number : 311722

10/100/1000 to 1000SX Media conv. MultiMode Duplex SC 550m

Part/number : 311756

Allied AT-MC102XL tx-fx fast ethernet media convert sc 2km

Part/number : 522102

SWITCH 4 RJ45 10/100 + FIBER 100FX MULTIMODE SC 2KM

Part/number : 311746

DEXLAN 60W High Power Media Converter

Part/number : 311760

10/100/1000 to 1000LX Media conv. SingleMode 20KM SC

Part/number : 311721

PLANET FTP-802 Media Converter FX to TX Multimode 2Km

Part/number : 410802

More than a Fiber Media Converter -- a Power over Ethernet Injector as well
The best data link and power sourcing solution for long reach network equipment
PLANET FTP-80x series is ideal for remote network equipment deployments, using two networking technologies:
- Media Conversion : 100Base-FX to 10/100Base-TX
- Power over Ethernet : Power Sourcing Equipment(PSE), PoE Injector
Providing both PoE and Fiber Optical interfaces, the FTP-80x is ideal for service providers, campuses and public areas requiring to deploy the PoE for wireless access points, IP-based surveillance cameras or IP phones in any places easily, efficiently and cost effectively.

Main features:

- Complies with IEEE 802.3, IEEE 802.3u 10/100Base-TX, 100Base-FX, IEEE 802.3af
- Power over Ethernet standards
- Auto negotiation for 10/100Base-TX half duplex mode or full duplex mode, auto-MDI / MDI-X function
on copper port
- IEEE 802.3x full duplex flow control and back pressure in half duplex eliminates packets loss
- Provides DC 48V power over RJ-45 Ethernet cable to devices with Ethernet port
- Auto-detect of PoE IEEE 802.3af equipment and protects devices from being damaged by incorrect installation
- 100Base-FX interface for up to 2km (multi-mode fiber 50µm/125µm, 62.5µm/125µm) on FTP-802
- 100Base-FX interface for up to 15km (single-mode fiber 9µm/125µm) on FTP-802S15
- DIP-switch: LFP (Link Fault Pass-through) mode selection
- Compact in size, easy to install
- LED indicators for easy network diagnostics

Wall mountable and Rackmountable Tray for 4 Units of Media Converter

Part/number : 522004

SWITCH 8 RJ-45 10/100 + 1 FIBER 100FX MULTIMODE SC 2KM

Part/number : 311747

PLANET FT-802S15 100FX Single Mode Media Converter- 15 km

Part/number : 411705

The PLANET FT-80x is a Fast Ethernet Bridge 100Base-FX fiber to 10/100Base-TX shielded twisted pair (STP) converter. It supports both half-duplex and full-duplex operations and a variety of fiber options. The converter auto-adapts to the highest level of performance supported by the device connected to the STP port. When the device is a switch or a workstation that supports full duplex, the converter adapts to the full-duplex mode and provides an effective 200Mbps bandwidth. When the connected device is a hub or a workstation that supports only half duplex, the converter adapts to the half-duplex mode and provides the nominal 100Mbps bandwidth. An override switch provides total manual control over the half/full-duplex operation, in fiber-optic interface. The fiber port of the converter operates at 1310 nm and uses SC connectors. Operation distance up to 15 km over single mode fiber.

The FT-80x series is with LFP (Link Fault Pass through function) (LLCF/LLR) and the DIP switch design. LLCF/LLR can immediately alarm administrators in case of a problem on the link and provide efficient solutions to monitoring the net. The DIP switch allows you to disable/enable the LFP function.

LLCF (Link Loss Carry Forward) means that when a device is connected to the converter and the TP line loses the link, the converter's fiber will disconnect the link of transmit. LLR (Link Loss Return) means when a device is connected to the converter and the fiber line loses the link, the converter's fiber will disconnect the transmit link. Both can immediately alarm administrators.

- 10/100Base-TX to 100Base-FX SC Bridge Media Converter - 15km
- Complies with IEEE 802.3, IEEE 802.3u 10/100Base-TX, 100Base-FX Standard
- Connectors: One RJ-45 (Auto-MDI/MDI-X) twisted pair, EIA568/ One fiber-optic, 1310nm wavelength
Data Transfer Rate:
- TP: 10/100Mbps
- FX: 100Mbps
Duplex mode support:
- Full or half-duplex mode by Auto-Negotiation (TP)
- Full or half-duplex mode by DIP-switch (FX)
LED indicators: PWR, FX LNK/ACT, FX FDX/COL, TP 100, TP LNK/ACT, TP FDX/COL
DIP-switch: 2 DIP-switches
- Rear DIP-switch: FX duplex mode selection
- Side DIP-switch: LFP (Link Fault Pass-through) mode selection

PLANET GTP-805A Gigabit PoE Converter 802,3af-SFP

Part/number : 411815

High-speed fiber to copper gigabit converter with 30W PoE+ injector: The converter is ideal for IP cameras or Wi-Fi dual-band hot-spots remote installation.

Specifications:

- On the fiber side: 550nm for multimode and 10 km for single mode link
- On the copper side: self-powered Data+Power 1000Mbps over 100 m.
- PoE+ IEEE802.3af/at active injector (PSE 30W)
- Compatible with Class ¾ IP PoE cameras
- Fiber optic port: SFP slot for MiniGBiC module insertion (1000SX or 1000LX)
- RJ-45 Port: 10/100/1000 with Auto MDI/MDI-X function/ MidSpan PoE 4/5(+), 7/8(-)
- External power supply included: 110/230V-52V DC 0.58A
- Dimensions: 26 x 70 x 94mm
- Weight: 210g

Allied AT-MC101XL tx-fx fast ethernet media convert st 2km

Part/number : 522101

DUAL SPEED MEDIA CONVERTER 2 X SFP 1000M PORTS

Part/number : 311882

ALLIED AT-SPTX MODULE SFP RJ-45 GIGABIT

Part/number : 522796

Web Manageable 1000Base-TX to SFP 100/1G

Part/number : 411915

Allied AT-MCR1 1 slot media converter rackmount chassis

Part/number : 522001

INDUSTRIAL MEDIA CONVERTOR RJ45/100FX MultiMode SC -2Km

Part/number : 314701

100FX / RJ-45 media converter designed to extend your network up to a 2-km distance outdoors or in industrial environment.
The broad operation temperature range can operate in any weather.

Specifications:
- 1 x RJ-45 100Mbps port
- 1 x Fiber Multimode Duplex 100FX SC connector
- 2 fixing kits for wall mount or DIN rail installation

Mini Media Converter 10/100T to 100BASE-FX MM, SC connector

Part/number : 522207

Allied AT-MCR1 1 slot media converter rackmount chassis

Part/number : 522003

PLANET Industrial Switch- 4 x 10/100 + 2 x 100FX SC MM- 2 km

Part/number : 314706

This fiber media converter has 2 fiber ports and a 4-port embedded copper switch.
You can expand your network by cascading the converters up to 2 km.

The heavy-duty design makes this converter ideal for rough environments. It supports
extreme temperatures.

Product features:

- 4 x 100Mbps RJ-45 auto-MDIx ports
- 2 x 100FX duplex SC fiber ports
- Fiber optic signal: 100FX 1310nm
- Compatible with Multimode 50/125µm / 62.5/125µm (2km max) fiber
- RJ-45 copper transmission: 10/20Mbps in Half/Full-Duplex, 100/200Mbps in Half/Full Duplex
- Fiber optics transmission: 200Mbps in Full-Duplex
- Protection index: IP30
- Supported temperature ranges: -40° to +75° / 5 à 90% humidity rate
- Two installation modes: DIN rail or wall-mounted
- Power supply: 2 x 48V with alarm output
- Protection: Ethernet 6KV DC / Power supply 6KV DC / Reversed polarity
- Dimensions : 135 x 97 x 32 mm - 442gr

HUAWEI FIBER MODULE MULTIMODE MINIGBIC SR 300M

Part/number : 101520

SWITCH 2 GIGA SFP + 2 GIGALAN 10/100/1000

Part/number : 311944

NETGEAR AGM731F

Part/number : 315100