Fiber converters and chassis - Page 3

TP-LINK MC200CM Gigabit Ethernet Media Converter

Part/number : 311915

The MC200CM is a media converter designed to convert 1000BASE-SX fiber to 1000Base-T copper media or
vice versa. Designed under IEEE802.3ab 1000Base-T and IEEE802.3z 1000Base-SX standards, the MC200CM is compatible with multi-mode fiber cable utilizing the SC-Type connector. The MC200CM supports shortwave (SX) laser specification at a full wire speed forwarding rate. It works at 850nm on both transmitting and receiving data.

Other features of this module include the ability to be used as a stand alone device (no chassis required) or with TP-LINK´s 19´system chassis, Auto MDI/MDI-X for TX port, and front panel status LEDs. The MC200CM will transmit at extended fiber optic distances utilizing multi-mode fiber up to 0.55 kilometers(0.342 miles).

•Complies with IEEE 802.3ab and IEEE 802.3z
•Provides switch configuration of Force /Auto transfer mode for FX port
•Extends fiber distance up to 0.55km(0.342 miles)

TP-LINK MC110 CS Fast Ethernet Media Converter

Part/number : 311914

The MC110CS is a media converter designed to convert 100BASE-FX fiber to 100Base-TX copper media or vice versa. Designed under IEEE 802.3u 10/100Base-TX and 100Base-FX standards, the MC110CS is compatible with single-mode fiber cable over the SC-Type connector. The MC110CS supports longwave (LX) laser specification at a full wire speed forwarding rate. It works at 1310nm on both transmitting and receiving data.

Other features of this module include the ability to be used as a stand-alone device (no chassis required) or with TP-LINK´s 19´´ system chassis, Auto MDI/MDI-X for TX port, Auto negotiation of duplex mode on TX port, supports both 5VDC and 9VDC external power supply and front panel status LEDs. The MC110CS will transmit at extended fiber optic distances utilizing single-mode fiber up to 20 kilometers(12.4 miles).

Main Features:

•Complies with 802.3u 10/100Base-TX, 100Base-FX standards.
•Link Fault Passthrough and Far End Fault minimize the loss caused by link failure timely
•Provides switch configuration of Half-Duplex / Full-Duplex transfer mode for FX port.
•Extends fiber distance up to 20km(12.4 miles)

TP-LINK MC100CM Fast Ethernet Media Converter

Part/number : 311911

The MC100CM is a media converter designed to convert 100BASE-FX fiber to 100Base-TX copper media or vice versa. Designed under IEEE 802.3u 10/100Base-TX and 100Base-FX standards, the MC100CM is designed for use with multi-mode fiber cable utilizing the SC-Type connector. The MC100CM supports longwave (LX) laser specification at a full wire speed forwarding rate. It works at 850nm on both transmitting and receiving data.

Other features of this module include the ability to be used as a stand alone device (no chassis required) or with TP-LINK´s 19´´system chassis, Auto MDI/MDI-X for TX port, Auto negotiation of duplex mode on TX port, supports both 5VDC and 9VDC external power supply and front panel status LEDs. The MC100CM will transmit at extended fiber optic distances utilizing multi-mode fiber up to 2
kilometers(1.2 miles).

•Complies with 802.3u 10/100Base-TX, 100Base-FX standards
•Link Fault Passthrough and Far End Fault minimize the loss caused by link failure timely
•Provides switch configuration of Half-Duplex / Full-Duplex transfer mode for FX port
•Extends fiber distance up to 2km(1.2 miles)

TP-LINK TL-SM321B-2 1000BASE BX WDM BIDIRECTIONAL SFP MODULE

Part/number : 311908

TP-LINK MC111CS WDM Fast Ethernet Media Converter

Part/number : 311904

The MC111CS is a media converter designed to convert 100BASE-FX fiber to 100Base-TX copper media or vice versa. Adopting WDM technology, MC111CS takes only one fiber cable to transmit and receive data, which will save half the cabling. Designed following the IEEE 802.3u 10/100Base-TX and 100Base-FX standards, the MC111CS is compatible with single-mode fiber cable over the SC-Type connector. The MC111CS supports longwave (LX) laser specification at a full wire speed forwarding rate. It works at 1550nm on transferring data and at 1310nm on receiving data. So the other end device to cooperate with the MC111CS should work at 1310nm on transferring data and at 1550nm on receiving data. Another TP-LINK´s media converter MC112CS is just one of the examples to cooperate with MC111CS.

Other features of this module include the ability to be used as a stand-alone device (no chassis required) or with TP-LINK´s 19´´ system chassis, Auto MDI/MDI-X for TX port, Auto negotiation of duplex mode on TX port, and front panel status LEDs. The MC111CS will transmit at extended fiber optic distances utilizing single-mode fiber up to 20 kilometers(12.4 miles).

•Complies with 802.3u 10/100Base-TX, 100Base-FX standards
•Link Fault Passthrough and Far End Fault minimize the loss caused by link failure timely
•Adopts WDM technology, transmitting and receiving data on one single fiber

TP-LINK MC111CS WDM Fast Ethernet Media Converter

Part/number : 311903

The MC111CS is a media converter designed to convert 100BASE-FX fiber to 100Base-TX copper media or vice versa. Adopting WDM technology, MC111CS takes only one fiber cable to transmit and receive data, which will save half the cabling. Designed following the IEEE 802.3u 10/100Base-TX and 100Base-FX standards, the MC111CS is compatible with single-mode fiber cable over the SC-Type connector. The MC111CS supports longwave (LX) laser specification at a full wire speed forwarding rate. It works at 1550nm on transferring data and at 1310nm on receiving data. So the other end device to cooperate with the MC111CS should work at 1310nm on transferring data and at 1550nm on receiving data. Another TP-LINK´s media converter MC112CS is just one of the examples to cooperate with MC111CS.

Other features of this module include the ability to be used as a stand-alone device (no chassis required) or with TP-LINK´s 19´´ system chassis, Auto MDI/MDI-X for TX port, Auto negotiation of duplex mode on TX port, and front panel status LEDs. The MC111CS will transmit at extended fiber optic distances utilizing single-mode fiber up to 20 kilometers(12.4 miles).

•Complies with 802.3u 10/100Base-TX, 100Base-FX standards
•Link Fault Passthrough and Far End Fault minimize the loss caused by link failure timely
•Adopts WDM technology, transmitting and receiving data on one single fiber

TP-LINK MC220L Gigabit Ethernet Media Converter

Part/number : 311898

The MC220L is a media converter designed to convert 1000BASE-SX/LX/LH fiber to 1000Base-T copper media or vice versa. Designed under IEEE802.3ab 1000Base-T and IEEE802.3z 1000Base-SX/LX/LH standards, the MC220L is designed for use with multi-mode/single-mode fiber cable utilizing the SC/LC-Type connector. It works at 850nm on both transmitting and receiving data when adopting multi-mode fiber and 1310nm on both transmitting and receiving data when adopting single-mode.

Main Features:

•Complies with IEEE 802.3ab and IEEE 802.3z
•Hot-swappable FX port
•Extends fiber distance up to 0.55km(0.342 miles) for multi-mode fiber and 10km(6.2 miles) for single-mode fiber

DUAL SPEED MEDIA CONVERTER 2 X SFP 1000M PORTS

Part/number : 311882

FIBER CONVERTER- GIGABIT MULTI TO SINGLE SC Duplex

Part/number : 311878

GIGABIT SWITCH 10 PORT W/ 8 PORT SFP 1000SX/LX

Part/number : 311848

2 port 1000M PoE 30W PSE+1port 1000M SFP Fiber Optical

Part/number : 311793

TP-LINK MC111CS WDM Fast Ethernet Media Converter

Part/number : 311918

The MC111CS is a media converter designed to convert 100BASE-FX fiber to 100Base-TX copper media or vice versa. Adopting WDM technology, MC111CS takes only one fiber cable to transmit and receive data, which will save half the cabling. Designed following the IEEE 802.3u 10/100Base-TX and 100Base-FX standards, the MC111CS is compatible with single-mode fiber cable over the SC-Type connector. The MC111CS supports longwave (LX) laser specification at a full wire speed forwarding rate. It works at 1550nm on transferring data and at 1310nm on receiving data. So the other end device to cooperate with the MC111CS should work at 1310nm on transferring data and at 1550nm on receiving data. Another TP-LINK´s media converter MC112CS is just one of the examples to cooperate with MC111CS.

Other features of this module include the ability to be used as a stand-alone device (no chassis required) or with TP-LINK´s 19´´ system chassis, Auto MDI/MDI-X for TX port, Auto negotiation of duplex mode on TX port, and front panel status LEDs. The MC111CS will transmit at extended fiber optic distances utilizing single-mode fiber up to 20 kilometers(12.4 miles).

•Complies with 802.3u 10/100Base-TX, 100Base-FX standards
•Link Fault Passthrough and Far End Fault minimize the loss caused by link failure timely
•Adopts WDM technology, transmitting and receiving data on one single fiber

DEXLAN 60W High Power Media Converter

Part/number : 311760

10/100/1000 to 1000SX Media conv. MultiMode Duplex SC 550m

Part/number : 311756

MEDIA CONVERTER MULTIMODE 100FX SC 2 RJ45-2 KM

Part/number : 311753

SWITCH 8 RJ-45 10/100 + 1 FIBER 100FX MULTIMODE SC 2KM

Part/number : 311747

SWITCH 4 RJ45 10/100 + FIBER 100FX MULTIMODE SC 2KM

Part/number : 311746

MEDIA CONVERTER SINGLE MODE 100FX SC+LFP-25KM

Part/number : 311726

10/100/1000 to 1000LX Media conv. W/SFP SingleMode 20KM LC

Part/number : 311722

10/100/1000 to 1000LX Media conv. SingleMode 20KM SC

Part/number : 311721

Media converter Fast Ethernet to 100FX SC Multimode 2KC

Part/number : 311703

10/100 SFP 100FX PORT MEDIA CONVERTER

Part/number : 311691

Dexlan 10/100 sfp 100FX port media converter

Part/number : 311690

This media converter is equipped with an STP RJ-45 port with auto-negotiation function and an SFP slot. You can adapt the media converter depending on your network, by inserting a MiniGBiC module (not included) for single-mode or multimode link implementation.
Depending on the transceiver, the transmission distance can reach up to 2km in multimode fiber and up to 10km in single-mode fiber.

Specifications:

- Compatible with IEEE802.3 and IEEE802.3u standards
- Data transfer rate up to 100Mbps in Full Duplex mode on the fiber and copper ports
- Auto-negotiation and Auto MDI/MDI-X functions supported by the RJ-45 port
- Compatible with IEEE802.1Q VLAN Tag and Spanning Tree protocols
- SFP slot for 100FX multimode or single-mode transceiver insertion, hot swappable
- 4 DIP switches for speed override and Link Fault Pass-through function setup

PLANET XT-905A

Part/number : 314910

PLANET FT-802 TX to FX Bridge Media Converter- 2km

Part/number : 411702

PLANET FT-802 TX to FX is a Fast Ethernet Bridge 100Base-FX fiber to 10/100Base-TX shielded twisted pair (STP) converter. It supports both half-duplex and full-duplex operations and a variety of fiber
options. The converter auto-adapts to the highest level of performance supported by the device connected to the STP port. When the device is a switch or a workstation that supports full duplex, the converter adapts to the full-duplex mode and provides an effective 200Mbps bandwidth. When the connected device is a hub or a workstation that supports only half duplex, the converter adapts to the half-duplex mode and provides the nominal 100Mbps bandwidth. An override switch provides total manual control over the half/full-duplex operation, in fiber-optic interface. The fiber port of
the converter operates at 1310 nm and uses SC connectors over multimode fiber.

The FT-80x series is with LFP (Link Fault Pass through function) (LLCF/LLR) and the DIP switch design. LLCF/LLR can immediately alarm administrators in case of a problem and provide efficient solutions to monitoring the net. The DIP switch allows you to disable or enable the LFP function.

LLCF (Link Loss Carry Forward) means that when a device is connected to the converter and the TP line loses the link, the converter's fiber will disconnect the transmission link. LLR (Link Loss Return) means that when a device is connected to the converter and the fiber line loses the link, the converter's fiber will disconnect the transmission link. Both can immediately alarm administrators of the problem on the link media and provide efficient solutions to monitoring the net.

Complies with IEEE 802.3, IEEE 802.3u 10/100Base-TX, 100Base-FX Standards
- Connectors: One RJ-45 (Auto-MDI/MDI-X) twisted pair, EIA568
- One fiber-optic, 1310nm wavelength, SC connector- 2km on multimode fiber
- Data Transfer Rate:
- TP: 10/100Mbps
- FX: 100Mbps
Duplex mode support:
- Full or half-duplex mode by Auto-Negotiation (TP)
- Full or half-duplex mode by DIP-switch (FX)
- LED indicators: PWR, FX LNK/ACT, FX FDX/COL, TP 100, TP LNK/ACT, TP FDX/COL
- DIP-switch: 2 DIP-switches
- Rear DIP-switch: FX duplex mode selection
- Side DIP-switch: LFP (Link Fault Pass-through) mode selection